Mr-Glass Custom & Geometric Windows Nationwide | TruePane Windows & Doors

Mr-Glass Custom & Geometric Windows in West Palm Beach: What to Know First

We repair and replace Mr-Glass custom and geometric windows throughout West Palm Beach, and most jobs are completed in a single visit. Expect honest line-item pricing before any work begins, with no surprise charges on the bill at the end of the day. If you own a Mr-Glass arched, radius, or odd-angle window that’s fogged, binding, or leaking, call (561) 264-1279 and a live person will answer.

Call (561) 264-1279

This page is written for homeowners in West Palm Beach who bought Mr-Glass windows years ago and now have a shaped or oversized unit that’s failing. We’re an independent Mr-Glass service provider, not a factory-authorized dealer, which means we make decisions based on what’s right for your house, not what protects a manufacturer’s margin.

How Mr-Glass Products Fail - and How We Fix Them

• Fogged sealed units in radius and arch tops. Mr-Glass built a lot of custom-radius insulated glass for 1990s and early-2000s West Palm Beach homes, and we routinely see seal failure around the curved bottom corners. The cause is usually the same: the original spacer wasn’t bent to match the radius precisely, so stress concentrated at the corners. We order replacement IGUs with the radius templated from your actual frame, not from a brochure drawing.
• Binding sashes on oversized fixed-picture units with operable flankers. When a Mr-Glass geometric window sits between two casements or awnings, the frame carries more racking load than a standard rectangle. Over a decade of Coastal Florida humidity cycles, the main frame can twist a few degrees. Most companies try to shim the sash; we pull the unit, check the rough opening for square, and correct the frame before reinstalling. If it is not square, plumb, and sealed, it is not done.
• Worn roller assemblies on Mr-Glass sliding geometric units. Mr-Glass made some trapezoid and parallelogram sliders for mid-century West Palm Beach ranches, and the rollers they used were not rated for daily use in sandy coastal air. They bind, the wheels flatten, and the panel starts grinding metal-on-track. We keep an inventory of aftermarket heavy-duty rollers with sealed bearings, which outlast the originals by years.
• Water intrusion at the sill on eyebrow and full-circle windows. Geometric windows have more perimeter sealant per square foot of glass than any rectangle, and Mr-Glass factory glazing from that era used a butyl tape that hardens and cracks in West Palm Beach’s UV. We remove all old glazing, clean the reglet, and re-seal with a marine-grade silicone that stays flexible. Then we water-test with a hose before we call the job done.
• Hazing and mineral etching on Mr-Glass tempered units near sprinklers or pool decks. West Palm Beach irrigation water is hard enough to etch glass over time, and geometric windows near pool equipment or lawn sprinklers take the worst of it. If the glass is hazed and the frame is still sound, we can often replace just the glass with a high-performance low-E IGU instead of rebuilding the whole geometric window. That keeps the job inside the existing opening and saves you the cost of new trim and stucco work.

Our Mr-Glass Custom & Geometric Windows Process

1. 1
   You call (561) 264-1279. A live person answers, takes the address and a description of the window problem, and schedules a visit that works for you. No call center, no voicemail tree.
2. 2
   We measure and diagnose. A background-checked, uniformed technician arrives on time, inspects the unit, checks the rough opening with a level and tape, and photographs everything. Every opening gets measured twice.
3. 3
   We write the quote on paper, side by side. You see the OEM Mr-Glass option and, where it makes sense, a quality aftermarket alternative with the price difference stated plainly. Both manufacturer warranty durations go in writing before you decide anything.
4. 4
   We order to spec. For custom shapes, we template the exact curvature and angles from your existing frame, not from a generic radius chart. That’s the difference between glass that drops in and glass that gets forced in.
5. 5
   We install, seal, and test. The old unit comes out, the opening gets checked for square, the new unit goes in level and plumb, and we water-test before we clean up. Most Mr-Glass geometric window replacements are done in one visit.
6. 6
   We register the warranties and stand behind the work. Both manufacturer warranty layers are registered in writing before the truck leaves your driveway. Our Done Right Promise covers the workmanship, no fine print and no arguing.

What Mr-Glass Custom & Geometric Windows Cost in West Palm Beach

What moves the price: whether the glass is tempered, whether you need impact-rated replacement glass to meet West Palm Beach code, the true radius or angle of the shape, and how much stucco or trim has to come off to reach the frame. We quote a fixed number before we start, not an estimate that drifts. Call (561) 264-1279 for a free estimate on your specific window.

Why West Palm Beach Homeowners Call TruePane Windows & Doors for Mr-Glass Work

We’ve been working on Palm Beach County windows since 2008, and Dale Kessler started TruePane in 2008 because he kept seeing the same thing: out-of-true installs and warranty paperwork that protected the manufacturer more than the homeowner. Our Done Right Promise is a written guarantee, not a verbal one. If it’s not done right, we make it right. Both manufacturer warranty layers get registered in writing with durations stated, before our truck leaves your driveway.

When a Mr-Glass geometric window can’t be economically repaired, we’ll tell you that directly and quote replacement lines side by side. We’re an authorized installer for more than a dozen manufacturers, including PGT, CGI, CWS, and ES Windows, so you get a real comparison, not whatever one brand happens to offer. A live person answers our phone 24 hours a day, 7 days a week. Call (561) 264-1279.

FAQs