Andersen Door Installation Nationwide | TruePane Windows & Doors

Andersen Door Installation: The West Palm Beach Owner’s Guide

Andersen door installation in West Palm Beach typically runs $380 to $1,400 installed, depending on whether we’re rebuilding the existing frame or replacing a failed component like rollers, hinges, or weatherstripping. We stock Andersen-compatible hardware on our trucks and can usually complete the work in a single visit. Most owners discover the problem the same way: the door starts dragging on the threshold in the afternoon heat, or a hinge pin has worn enough that the slab drops a quarter inch and the latch no longer lines up with the strike plate. What started as a door you have to lift slightly to close becomes a door that scrapes, sticks, or lets daylight through around the edges.

Call (561) 264-1279

In West Palm Beach, the salt air and humidity don’t just age the finish. They work on the hardware underneath. We see certain Andersen hinge sets and roller assemblies fail years faster here than they would in, say, inland Georgia, because corrosion gets into the moving parts that were never meant to fight that kind of moisture load. The good news is that most of these failures are repairable without replacing the entire door slab, which is why knowing what to look for early saves real money.

Which Andersen Models This Applies To

This page covers the Andersen door lines we most commonly service and install across West Palm Beach: the 200 Series, 400 Series, A-Series, and the older Narroline and Frenchwood hinged doors that are still in thousands of homes from Flamingo Park to Ibis Golf and Country Club. The 200 and 400 Series use a different hinge and roller geometry than the A-Series, and that matters because the part numbers do not interchange. A hinge kit for a 400 Series Frenchwood door will not seat correctly on a 200 Series slab. We’ve caught that mistake on jobs where another contractor ordered by price instead of by model.

Here’s the compatibility gotcha Andersen owners should know: the glass panel cannot tell you which series you have. You need to read the etched logo in the corner of the glass and the serial number on the edge of the door slab or on the hinge stile. We read both before we order anything. Andersen’s OEM parts carry a warranty and are our default recommendation for load-bearing hardware like hinges, multipoint lock sets, and Frenchwood roller assemblies. For weatherstripping and sweeps, we often use quality aftermarket equivalents that match or beat OEM performance in coastal humidity at a lower cost. We’ll quote both side by side on paper before any work begins, which is part of The Keystone Standard we apply to every Andersen job.

Signs Your Andersen Door Installation Is Failing

• The door scrapes across the threshold in the late afternoon. Thermal expansion in direct sun bows the slab just enough that a worn hinge or settled frame shows itself. What grips at noon may close fine at midnight. The fix is rarely the threshold alone; it’s usually hinge or roller wear that has changed the slab’s swing geometry.
• The locking point binds against the strike plate. Over years of use, Andersen multipoint hardware drifts out of alignment. If you have to lift or push the slab inward while turning the handle, the rollers or hinge pins have worn past their tolerance. Forcing the lock puts strain on the gearbox inside the handle assembly and turns a $200 alignment into a $600 replacement.
• Daylight around the weatherstripping on the hinge side. This is more than an air leak. The weatherstrip along the hinge stile is the first line of defense against wind-driven rain, and in West Palm Beach, that’s a real structural concern during summer storms. Once you can see light, the door has shifted out of square and the weatherstrip is no longer compressing evenly.
• The Frenchwood roller or sliding panel sounds like it’s grinding gravel. Andersen sliding door rollers are sealed bearings. When the seal fails in coastal air, the bearing rusts and the nylon wheel stops rolling. The panel then slides metal-on-track, and every pass is gouging the rail. That’s a roller replacement plus possible track work if it runs too long.
• You can hear wind whistling through a closed, locked door. That means the panel alignment is off or the weatherstripping has compressed permanently and lost its memory. Andersen’s compression seals do not bounce back once they’ve set in a worn position. In West Palm Beach, that’s money leaking out of your electric bill every month the air conditioner runs.

Replacement Cost & What’s Included

In West Palm Beach, you should expect to pay between $180 and $340 for a typical Andersen hinge kit or roller replacement on a standard 6/8 by 2/6 or 3/0 Frenchwood door, including labor. A full door installation where the frame needs rebuilding or a custom-size slab has to be ordered runs $800 to $1,400, and lead time on custom Andersen sizing is usually two to four weeks depending on the production schedule. That’s a reality of buying an Andersen product: the custom lines are built to order, not sitting on a shelf.

Here’s what drives the price:

• Part type and series: OEM Andersen hinge kits and multipoint locks cost more than weatherstripping, and A-Series hardware runs higher than 200 Series. We stock the common 200 and 400 Series wear parts on the truck; the rest we order with exact model verification before placing the order.
• Labor reality: A simple roller swap on a sliding panel is a one-person, two-hour job. Rebuilding an out-of-square hinged frame is a half-day or more, because we do not shim-and-caulk our way around a structural problem. When we find rot or settling, we tell you before we start cutting and the price is written down before the first tool comes off the truck.
• Warranty registration: Both warranty layers get registered in writing before our truck leaves your driveway. Every job carries our Done Right Promise: if it is not done right, we make it right. No paperwork fights, no arguing.

We stand behind the work, the warranty, and the promise, in writing. That’s the deal.

DIY or Call Us?

What you can safely do yourself: clean the track on a sliding Andersen panel with a brush, not a pressure washer, and check whether the door slab is visibly dropped on the hinge side by measuring the gap at the top corner versus the bottom. Those diagnostics tell us a lot before we even arrive. What you should not do yourself is pull the hinge pins on a heavy Andersen door slab or attempt to re-rack the frame. A wood-clad Frenchwood door can weigh over 150 pounds. When it comes off its hinges, it comes down fast, and improperly seated hinge pins are how people lose fingers or crack tile. This is work we do with two people and the right support equipment.

If you’ve verified the model serial and you’re seeing any of the failure signs above, call us at (561) 264-1279. We’ll measure, quote, and fix it. The estimate is free.

FAQs