Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Roof Replacement & Installation in West Palm Beach: What to Know First
We replace and install CGI roof systems and components for homeowners throughout West Palm Beach, and most jobs are completed within one to two weeks of the estimate. You’ll get a written line-item quote before any work starts, so the number you approve is the number you pay. As an independent CGI service provider, we diagnose what’s actually failing and fix it without pushing a full replacement when a targeted repair will do the job.
If you own a CGI roof product that’s leaking, lifting, or showing its age, call (561) 264-1279. A person answers, every time, and we’ll talk through what you’re seeing before we ever schedule a truck.
Key Takeaways:
- Independent CGI roof replacement and installation in West Palm Beach, with written pricing and no surprise change orders
- We name the failure first, then quote the fix, repair or full replacement
- Both warranty layers registered in writing before we leave your driveway
- Live person on the phone 24 hours a day, seven days a week
How CGI Products Fail, and How We Fix Them
CGI builds a solid product, which is why so many West Palm Beach homes carry them. But nothing built for hurricane country lasts forever, and we see the same failures repeat across neighborhoods from El Cid to Ibis. Here’s what actually goes wrong, and what we do about it.
- Weep hole and drainage channel clogging on CGI Estate Collection roof panels. West Palm Beach’s rainy season pushes leaf debris, sand, and salt spray into roof drainage paths. When the weep holes clog, water backs up under the panel lap and finds its way inside. We remove the affected panels, clear every drainage channel, replace any corroded flashing, and re-seat the lap so water sheds the way the original engineer intended.
- Neoprene gasket compression set on CGI Sentinel series fastening points. Fastener gaskets flatten over ten to fifteen years in South Florida heat, and once they lose rebound, every fastener becomes a potential drip. We don’t re-torque old gaskets and call it done. We pull the fastener, inspect the substrate underneath, replace the gasket with a matched-durometer seal, and only then re-set and torque to CGI’s published spec.
- Corrosion at panel overlap seams near the Intracoastal. Salt air loves aluminum lap joints, and homes within two miles of the water show seam corrosion first. We strip the seam, treat any surface oxidation, replace the lap sealant with a marine-grade product rated for continuous salt exposure, and re-fasten the lap with corrosion-matched hardware. Skipping the surface treatment step is exactly how you end up redoing this repair in three years.
- Improperly flashed penetrations around vent pipes and skylights on older CGI roof installations. A lot of West Palm Beach roof work from the 1990s and early 2000s used whoever was cheapest, and the pipe boots and curb flashing failed long before the CGI panels did. We re-flash every penetration with the correct gauge and profile for CGI’s panel geometry, not a one-size-fits-all boot from a big-box shelf.
- Transit and storage damage on new CGI panel installs. We’ve unwrapped factory pallets and found panels with creased ribs from strapping that was too tight. A creased rib won’t show a leak on day one, but it will in the first hard wind storm. On every new installation, we inspect every panel before it leaves the ground, and anything with a crease, a deep scratch through the coating, or a bent leg gets set aside and returned. You don’t pay for panels we won’t stand behind.
Our CGI Roof Replacement & Installation Process
Here’s how a typical CGI roof job goes from first call to final walk-through.
- 1
Phone call and history. You tell us what you’re seeing. We ask about when it started, where the stains show inside, and what brand and approximate age the roof is. If you have paperwork from the original install, that helps, but it’s not required.
- 2
On-site inspection and diagnostic. A background-checked TruePane technician walks the roof and the attic, checks the panel laps, flashings, fasteners, and drainage paths, then documents what’s failing with photos. You’ll see what we see.
- 3
Written quote with parts decisions made plain. If CGI factory parts are available and make sense for the job, we quote OEM. If a quality aftermarket part does the same job at a better price, we say so in writing and let you choose. No mystery markup, no “we’ll see once we’re into it.”
- 4
Scheduling and tear-off or panel replacement. We set a date, show up on time, protect the landscaping and pool area, and stage materials so the roof deck is never exposed overnight.
- 5
Installation, inspection, and test. Every panel goes in square, plumb, and sealed. The founding rule in our shop is simple: if it is not square, plumb, and sealed, it is not done. We water-test the repaired or new sections, then walk the roof with you before we call the job complete.
- 6
Warranty registration and the Done Right Promise. Both manufacturer warranty layers get registered in writing before we leave the driveway. If something’s not right within 90 days, we fix it. No paperwork fights, no arguing.
What CGI Roof Replacement & Installation Costs in West Palm Beach
CGI roof work in West Palm Beach runs a wide range because the scope varies from a single panel swap to a full re-roof. Here’s what we see across the county:
- Single panel replacement or repair: $450 to $950, depending on panel length and whether flashing work is needed
- Flashing replacement at one or two penetrations: $350 to $800
- Partial re-roof of one roof plane: $4,500 to $9,000
- Full CGI roof replacement on a typical 2,000-square-foot West Palm Beach home: $18,000 to $34,000
- Full replacement with impact-rated panels and upgraded underlayment: $28,000 to $42,000
What moves the price: roof pitch and access, the condition of the existing deck, how many penetrations need re-flashing, and whether you’re in a coastal exposure zone that requires heavier-gauge panels. Every quote is line-itemed in writing, and the price we quote is the price you pay. Call (561) 264-1279 and we’ll come measure, inspect, and give you a number you can plan around. The estimate is free.
Why West Palm Beach Homeowners Call TruePane Windows & Doors for CGI Work
Dale Kessler grew up in Northwood Hills, spent summers watching his father re-glaze storefront windows along Dixie Highway, and has spent the better part of two decades setting, sealing, and standing behind glass and roof work across Palm Beach County. TruePane Windows & Doors was founded on a rule that hasn’t changed: if the pane is not true, the job is not done.
We’ve been serving this community since 2008, and we plan to be here in thirty more. Every job carries the Done Right Promise and The Keystone Standard, both manufacturer warranty layers registered in writing, durations stated. When a homeowner calls with a question at 6 a.m. or 11 p.m., a live person answers. Not a voicemail tree, not a callback form. And while CGI is the focus here, we also service PGT, CWS, ES Windows, and ECO Window Systems, so if you have mixed brands across the house, one call covers it.
FAQs
No, roof replacement done by a qualified contractor using correct parts and installation practices does not void a CGI product warranty. What voids warranties is improper installation, unapproved sealants, or re-torquing fasteners beyond spec. That’s why we document every step and register both warranty layers in writing.
If you’re mid-replacement and wondering whether a product still carries coverage, call (561) 264-1279. We’ll help you check before any work begins.
In most cases, we can source close-match or direct-replacement panels for CGI’s common lines, including older Estate and Sentinel profiles. If a profile has been discontinued, we’ll show you the closest available match in writing and talk through your options, including whether a partial-plane replacement makes more sense than chasing a dead match.
A typical full replacement takes five to ten working days, depending on roof complexity, access, and weather. We schedule around the rainy season the same way you’d expect a roofer to, and we never leave a deck exposed overnight.
If the panel faces are sound and the issue is flashing, fasteners, or drainage, repair usually makes sense. If panels show widespread seam corrosion, creased ribs, or the coating is failing across multiple planes, replacement is typically the smarter long-term investment. We’ll show you the evidence either way and quote both options when it’s a close call.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving West Palm Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.